FIRMWARE RELEASE NOTES
                        ======================

Products affected: AXIS P7224 Network Camera

Release date:      2012-03-05

Release type:      Production

Firmware version:  5.40.7.1

File name:         P7224_5_40.bin

Preceding release: 5.40.7

AMC version:       6.0.6.4-1

------------------------------------------------------------------------------

UPGRADE INSTRUCTIONS
====================

The firmware can be upgraded using Axis Camera Management 2.0, HTTP or FTP.
Please follow the instructions from the user's manual, the web page at
http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named
howtoupgrade.txt.

Corrections since 5.40.7
========================

5.40.7:L32433
ptz.cgi returns unexpected values when no driver is installed on multi channel
products

5.40.7:L32429
Parameter PTZ.CamPorts.Cam#Port shall be -1 when no PTZ driver is installed.
However on multi channel products the value is always  > 0 for all but the
first channel.

5.40.7:L29780
Camera is not able to connect to the AVHS portal

5.40.7:L32251
Accessing the AVHS portal through a proxy does not work.

5.40.7:L32791
The quad view stream can in some circumstances be jerky and old images can be
seen in the video stream.

5.40.7:L32441
Missing recording functionality over network share for products with no SD-card
support.


Known Bug/Limitations
=====================

5.40.7:L1
Missing recording functionality over network share for products with no SD-card support.

5.40.7:L2
802.1x does not work in a Q7900 rack if a blade is placed in any of the rack positions 1, 5, 8, 11

5.40.7:L3
The 'Any' event does not work when triggered with the virtualinput.cgi

5.40.7:L4
It's not possible to get an event due to power-supply failure in a Q7900 rack

5.40.7:L5 
Parameter PTZ.CamPorts.Cam#Port shall be -1 when no PTZ driver is installed, However on multi channel products the value is always > 0 for all
but the first channel.

5.40.7:L6
 ptz.cgi returns unexpected values when no driver is installed on multi channel products

5.40.7:L7
 AVHS radio button not enabled after enable and save

5.40.7:L8
 In an AVHS installation, the clock is not synchronized with the AVHS server which may lead to incorrectly scheduled recordings.

5.40.7:L9 
ONVIF discovery source address is not correct. The link local address is used as a source address, this is not according to RFC 3927
(section 2.7):

5.40.7:L10 
When using the H.264 rate controller  with a low GOV length (e.g. 3) you can get disrupted video. Use GOV length > 10.

5.40.7:L11 
Network lost trigger is not available in Action rule setup.

5.40.7:L12 
TCP notify in an Action rule doesn't work as expected.

5.40.7:L13 
When action rules run, the name of the rule will sometimes be incorrectly logged in the system log.

5.40.7:L14
The center mode for click-in-picture doesn't work for ptz-control when using loadable drivers.

5.40.7:L15 
The sound level is very high when there is no audio source connected. If the high-pass filter in the audio codec is enabled the level will
be low.

5.40.7:L16 Invalid multicast address in SDP content. 

5.40.7:L17 90 and 270 rotation can cause a drop in frame rate.

=================================

The AXIS VAPIX Application Programming Interface is supported by the
AXIS P7224.

The following groups are supported by this product.
For more information, please refer to the AXIS VAPIX HTTP API specification
version 3, part of the AXIS VAPIX API, available at www.axis.com.

Group                  Exceptions
=====                  ==========
General
Image and Video
PTZ                    Set PTZ parameters (ptzparam.cgi)
Motion Detection
I/O
Serial port
IP filter
Audio
Active Storage


Built in templates for dynamic parameters are:

Template               Group
========               =====
'audioclipaction'      Event.E#.Actions
'button'               PTZ.Auxiliary.A1.Button
'event'                Event
'ftp_config'           EventServers.FTP
'ftpaction'            Event.E#.Actions
'guardtour'            GuardTour
'guardtouraction'      Event.E#.Actions
'http_config'          EventServers.HTTP
'httpaction'           Event.E#.Actions
'hwaction'             Event.E#.Actions
'mediaclip'            MediaClip
'motion'               Motion
'nsdevice'             NetworkShare
'ptzaction'            Event.E#.Actions
'ptzsensoraction'      Event.E#.Actions
'recordaction'         Event.E#.Actions
'smtpaction'           Event.E#.Actions
'streamcache'          StreamCache
'streamprofile'        StreamProfile
'tcp_config'           Eventservers.TCP
'tcpaction'            Event.E#.Actions
'tour'                 GuardTour.G#.Tour
'user_ctlqueue'        PTZ.UserCtlQueue


Supported AXIS VAPIX API Image Resolutions for AXIS P7224.

Resolution  Exceptions
==========  ==========
16CIF
1536x1152   1) 3)
1280x960    2) 3)
XGA
1024x768    3)
D1
720x576     1)
720x480     2)
4CIF
704x576     1)
704x480     2)
2CIF
704x288     1)
704x240     2)
CIF
352x288     1)
352x240     2)
QCIF
176x144     1)
176x120     2)

1) Only available for PAL cameras
2) Only available for NTSC cameras
3) Only available for Quad channel